$41.32
$70.66
Original item: One Only. The U.S. Model 1835 Musket was a .69 caliber smoothbore flintlock, with a 42-inch barrel and an overall length of 58 inches. It replaced the previous model 1822 musket, and often is viewed as a further development of that design. It was really only an incremental change, and many differences involved how the musket was produced, rather than the actual design. The emphasis was on making some interchangeable parts, and to use more accurate manufacturing methods. This paved the way for the later model of 1842, the first U.S. musket to have fully interchangeable parts. The Model 1835 was produced by the Springfield Armory, Harpers Ferry Armory, and numerous other contractors. It was eventually superseded by the model 1840 and 1842 muskets, the former of which was originally made in Flintlock, but most were converted to percussion before they made it to the field. The 1842 was only made in percussion. In the 1850s, many of the Flintlock Muskets in Arsenal were converted to Percussion, which was a much more reliable and water-resistant ignition system. This involved all variants of the Model of the 1816. This helped to standardize the types of ammunition carried by the soldiers in the field. Many were altered by Frankford Arsenal with the new Maynard Type primer locks and percussion bolsters made by the Remington Arms Co of New York. Remington Arms contracted with the government between 1856 to 1859 for 20,000 Maynard primer locks and bolsters and delivered all to Philadelphia’s Frankford Arsenal location. These were then fitted to the muskets during conversion, and the bores were rifled during this process. The rear sights were also replaced with ones similar to the Model 1855 Springfield. The outbreak of the Civil War in the United States created a large need for percussion muskets, as the number of modern firearms currently on hand was far short of what was needed. To fill this need, many muskets converted to percussion in the 1840s-1850s were pressed back into service, such as this example. This very interesting rifle began life as a Springfield Model 1835 Musket, most likely produced at either Springfield or Harpers Ferry. It could possibly be an 1822 model, but the barrels on those were usually not suitable for conversion to a rifled bore. The Maynard tape primer lock was one of the 20,000 produced by the Remington Arms Co., as indicated by markings on the tail of the lock plate: REMINGTON’SILION. N.Y.1858U.S. The lock functions correctly, holding at half cock and firing at full. The tape primer system looks to be complete, and the advancing pawl still moves upwards along with the lock, though we have no way to test to see if the system can still feed tape primer. The door is still present and opens correctly, with the springs inside still present, however it is quite easy to open, as the latching stud is missing, with only the spring remaining. The barrel tang is also dated 1857, and the left side of the breech is marked J.T. for inspector John Taylor, a Springfield Armory foreman who had supervised the manufacture of 6 pattern muskets for the alteration process. He was reassigned from inspection duties at Colt to the Remington factory to oversee and inspect the parts being made there. There is also an NJ surcharge on the left facet of the barrel, for issue to the state of New Jersey. There are some markings on the left side counterpane of the stock, however they are too faint to read. We did note large letters GLG on the left side of the stock, probably the initials of an owner. The musket’s mounts are all of iron and have a lovely polished gray matte patina over most parts, with no signs of past major oxidation or other issues. There are also some inspection marks stamped into some components, and the iron butt plate is stamped U.S.. There is no rear sight fitted to the barrel of the gun, and no sign that one was ever installed, which is not uncommon. There is definitely some powder burn around the cap nipple cone bolster, and the cone itself shows heavy oxidation, so the it looks to have seen a good amount of use after the percussion conversion. We checked the cleanout on the bolster, and it still easily removes for cleaning, however the screw may not be original. Both sling swivels are present and functional, and the musket still has an original ramrod with intact threads on the end, however it does not have a cupped front for engaging a rifle ball, so it is probably a period replacement. We checked the bore, and it is unfortunately heavily oxidized and fouled. We still can see some of the original rifling, but it is overall dark and was definitely not cleaned after being used. It looks to have seen a good amount of use after the percussion conversion. The one piece walnut stock is in very good condition, showing a lovely red brown color, only achieved after decades, or in this case, centuries of age. There are the expected dents, small chips, cracks, and gouges seen on a stock that has seen long service, however there is no major damage or evidence of repairs. There is a bit of cracking around front of the lock, a very common place to see this, and the stock does look to have been varnished long ago, which is very well retained.. A very nice example of a typical U.S. musket that was given new life by later modification. Many soldiers during the civil war were armed with this exact type of rifled musket. Hard to find in this lovely displayable condition and ready to display! Specifications:- Year of Manufacture: circa 1830 – converted 1857-1858Caliber: .69″ RifledCartridge Type: Ball and PowderBarrel Length: 42 InchesOverall Length: 57 1/2 InchesAction type: Side Action Percussion Lock with Tape PrimerFeed System: Muzzle Loading History of the Model 1835 Musket: The War of 1812 had revealed many weaknesses in American muskets. The Model 1812 Musket was created in an attempt to improve both the design and manufacture of the musket. The Model 1816 made further improvements, and replaced the Model 1812. The Model 1812 had borrowed heavily from the design of the French Charleville model 1777 musket, and this design was retained for the Model 1816. The Model 1816 had a 42 inch long .69 caliber smoothbore barrel, similar to the Model 1812, but had a longer lock plate, a shorter trigger guard, and a longer bayonet than the Model 1812. The Model 1816 also had a more straight lined stock. The overall length of the weapon was 58 inches. The Model 1816 musket was originally produced at the Harpers Ferry and Springfield Arsenals between 1816 and 1844. Around 675,000 were made, more than any other flintlock in U.S. history. The Model 1816 was originally produced as a flintlock musket. Like many flintlock muskets, many of these were later converted to percussion cap, as the percussion cap system was much more reliable and weather resistant. This model of Springfield musket was used by Texans during the Texas Revolution and by the US Army and militia during the Mexican-American War. During this conflict, the flintlock version of the Model 1816 was preferred by U.S. regular forces, due to percussion cap supply concerns. It was also used during the early years of the American Civil War until around 1862. Many improvements to the Model 1816 were made, producing the Model 1822, Model 1835, Model 1840, and Model 1842. U.S. Ordnance Department referred to these as different models, but in other U.S. government documents they are referred to as a continuation of the Model 1816. Modern histories are similarly inconsistent in the nomenclature of these weapons, often referring to them as “Type 2” and “Type 3” versions of the M1816. NOTE: International orders of antique firearms MUST be shipped using UPS WW Services (courier). USPS Priority Mail international will not accept these. International customers should always consult their country’s antique gun laws prior to ordering.
Wwii Original Items
